This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
tymcom-x-startup [2017/11/21 06:03] jms [Building a new monitor from sources] |
tymcom-x-startup [2018/04/04 09:12] (current) jms [Other pages] |
||
---|---|---|---|
Line 39: | Line 39: | ||
sim> exit | sim> exit | ||
- | ===== Create | + | ===== Create tym-*.ini files ===== |
==== tym-fresh.ini for " | ==== tym-fresh.ini for " | ||
- | Linux% cat tym-fresh.ini | + | Linux% cat x14-fresh.ini |
; SIMH Configuration for TYMCOM-X, refresh needed | ; SIMH Configuration for TYMCOM-X, refresh needed | ||
; Get sys: | ; Get sys: | ||
- | copy dskb.dsk | + | copy dskb.dsk |
- | copy dskc.dsk | + | copy dskc.dsk |
- | ; These two units now need initialize, DEFINE and REFRESH | + | ; These two units now need initializing, DEFINE and REFRESH |
- | attach rp0 tymb00.dsk | + | attach rp0 x14a.dsk |
- | attach rp1 tymb01.dsk | + | attach rp1 x14b.dsk |
- | ; Tape with TITO.SAV | + | ; Tape with TITO.SAV |
attach tu0 tito.tape | attach tu0 tito.tape | ||
- | set tim y2k | ||
expect " | expect " | ||
- | expect " | + | expect " |
expect "BAT pages on this UNIT?" send " | expect "BAT pages on this UNIT?" send " | ||
expect "BAT pages on this UNIT?" send " | expect "BAT pages on this UNIT?" send " | ||
Line 63: | Line 62: | ||
expect "NEW ID NEEDED" | expect "NEW ID NEEDED" | ||
expect " | expect " | ||
- | expect " | + | |
+ | | ||
+ | set cpu tops10 | ||
+ | set cpu idle | ||
boot rp | boot rp | ||
+ | |||
+ | Note: TYMCOM-X has a severe Y2K8 problem; it does not handle dates after November 8th, 2008. Use a date 28 years in the past to get the day-of-week correct. | ||
+ | ==== tym-dz11.ini for testing ==== | ||
+ | |||
+ | Same as '' | ||
+ | |||
+ | set dz 8b | ||
+ | attach -am dz | ||
+ | expect " | ||
+ | expect " | ||
==== tym-prod.ini for production ==== | ==== tym-prod.ini for production ==== | ||
Line 70: | Line 82: | ||
Linux% cat tym-fresh.ini | Linux% cat tym-fresh.ini | ||
; SIMH Configuration for TYMCOM-X, production | ; SIMH Configuration for TYMCOM-X, production | ||
- | attach rp0 tymb00.dsk | + | attach rp0 x14a.dsk |
- | attach rp1 tymb01.dsk | + | attach rp1 x14b.dsk |
; Tape with TITO.SAV | ; Tape with TITO.SAV | ||
attach tu0 tito.tape | attach tu0 tito.tape | ||
set tim y2k | set tim y2k | ||
expect " | expect " | ||
- | expect " | + | expect " |
boot rp | boot rp | ||
- | |||
===== Start up TYMCOM-X ===== | ===== Start up TYMCOM-X ===== | ||
Line 170: | Line 181: | ||
At this point you'll need to enter a time like " | At this point you'll need to enter a time like " | ||
+ | |||
+ | If '' | ||
| | ||
Checking all units on disk controller - reading UNIT ID from HOME pages. | Checking all units on disk controller - reading UNIT ID from HOME pages. | ||
Line 205: | Line 218: | ||
MTA0 assigned | MTA0 assigned | ||
| | ||
- | !run mta: | + | !get mta: |
+ | ?Address check for device MTA0 for location 002123; UUO at exec PC 143656 | ||
+ | |||
+ | !get mta: | ||
+ | ?Magtape HISEG format BAD or system errors | ||
+ | |||
+ | !get mta: | ||
?I/O error on file TITO.SHR | ?I/O error on file TITO.SHR | ||
+ | | ||
+ | !core | ||
+ | 174:1+0/512 pages | ||
+ | | ||
+ | !get mta: | ||
+ | ?I/O error on file TITO.SHR | ||
+ | | ||
+ | !core | ||
+ | 2:1+0/512 pages | ||
This is the current roadblock - cannot run tito.sav from tape (this also fails under TOPS-10). | This is the current roadblock - cannot run tito.sav from tape (this also fails under TOPS-10). | ||
Line 269: | Line 297: | ||
This is the current roadblock - cannot run tito.sav from tape (this also fails under TOPS-10). | This is the current roadblock - cannot run tito.sav from tape (this also fails under TOPS-10). | ||
+ | |||
==== Other pages ==== | ==== Other pages ==== | ||
- | [[tymcom-x|Overview]] page, [[tymcom-x-simh|SIMH Setup]] page, [[tymcom-x-startup|TYMCOM-X Startup]] page, [[tymcom-x-status|Status]] page. | + | |
+ | [[tymcom-x|Overview]] page, [[tymcom-x-simh|SIMH Setup]] page, [[tymcom-x-startup|TYMCOM-X Startup]] page, [[tymcom-x-tape|TITO on disk]] page, [[tymcom-x-status|Status]] page. | ||